Read these instructions completely before attempting an installation or update.
This document provides specific instructions on how to install or update Robot Space using the HelpSystems Product Loader. For general information about the HelpSystems Product Loader, see “Using the HelpSystems Product Loader.”
The Robot Space installation process creates or changes two Robot user profiles: RBTUSER and RBTADMIN. RBTADMIN has the attributes of a QSECOFR profile. RBTUSER has attributes like QPGMR. Directory entries are automatically added for the RBTADMIN and RBTUSER profiles. These profiles were created for the following reasons:
They satisfy requests from corporate auditors that our objects be owned differently from IBM objects.
They allow us to build a secure product for your environment.
They isolate Robot products from IBM changes to the QPGMR or QSECOFR profile defaults.
Note: If you have made any manual changes to the RBTUSER or RBTADMIN user profiles and their authorities, these changes will be lost with any product installation or conversion.
Before loading Robot Space, we check if RBTSYSLIB needs to be updated. If it does, you’ll be asked to bring down the subsystem RBTSLEEPER. This ends all Robot products running on your system. When the update completes, the subsystem will restart automatically.
For installs only: When you’re finished loading Robot Space, follow the steps below to enter the license code.
Once the installation or update process completes, read the After You Are Done section for additional information.
Important: We’ve greatly improved the bundled installers to make them easier to use. However, we recommend you read the installation/update/conversion instructions carefully before proceeding.
The system requirements for the current (non-archived) version are:
IBM i (i5/OS, OS/400) version V7R2 or higher
If you use any of the following products, they must be at the release/modification levels shown (or higher) to work properly with Robot Space 3.
Note: To see the version and modification level of each product you currently have installed, enter the command RSLVER on a command line.
Robot Alert R05M18
Robot Client R05M11
Robot Corral R02M09
Robot CPA R04M19
Robot Network (Host) R09M42
Robot Network (Node) R09M42
Robot Schedule R09M18
Robot System Library (RBTSYSLIB) R01M96
If you use network security software on your system, you should be aware that the Robot Space Explorer (the graphical user interface) uses the following servers and exit points:
We recommend that all these exit points be open to RBTUSER, RBTADMIN, and the users who will be using Robot Space.
Use these instructions to install or update Robot Space. This process downloads everything to your PC and loads the objects on the IBM i. Read the following steps carefully to proceed.
Download the Robot Space installer (setupSpace.exe) from My Downloads page on our website. Double-click it to start it.
On the Choose Components panel, select which components you want to install. You can choose to install the Software for Windows (the GUI and the Manuals) and the Software for IBM i. Click Next.
If you’re only installing the Software for Windows, the process completes and the installer closes. The Software for Windows has been installed. You can skip the rest of these steps.
Note: The manuals were installed at the following location.
C:\Program Files (x86)\Help Systems\Robot SPACE 3\manuals
If you’re loading the Software for IBM i (with or without the manuals), continue to step 4.
On the IBM i Details panel:
Select or enter the IBM i where you want to load Robot Space.
Enter a user profile and password that’s a member of the user class *SECOFR and has at least the following special authorities: *ALLOBJ, *SECADM, *JOBCTL, and *IOSYSCFG. The user profile should have Limit capabilities set to *NO. This profile will be used to restore and copy objects, and for product maintenance on the IBM i.
(Optional) In the Advanced Settings section:
Enter a port number or use the arrows if you want to change the FTP port number to something other than the default of 21.
Select Secure File Transfer if you want to use FTPS (FTP over SSL) during the file transfer. The default FTPS secure port is 990, but it can be changed to the required secure port for your environment.
In the Timeout (seconds) field, enter the number of seconds the session should be kept active during an FTP transfer. You can choose anywhere between 25 and 1800 seconds (30 minutes).
Note: If the transfer takes longer than the amount of time specified, the session will expire.
You have two options on the Product Load Options panel:
Click Immediate Load if you’d like to load the product on the IBM i now.
Note: If you're doing an update, this ends Robot Space until the product load completes. After you are done, we’ll restart the product.
Note: See “Loading Staged Objects on the IBM i” below for instructions on how to load the staged objects on your selected IBM i system.
The Product Load Progress panel for Robot Space launches. When the processing is complete, you have two choices:
If this is the only installation or update of Robot Space that you're doing, click Finish.
If you have installations or updates to do on other IBM i systems, click Restart. Then, return to step 4.
Note: If the Product Load Progress panel ends with an overall Failed message, the product upload could not complete properly. To find the reason the upload failed, click View Logs and review your logs. You can also use Download at the top of the logs to save the information for future review.
If you chose to stage your objects during step 5b of the installation or update process, do the following to manually load them on the IBM i you identified above.
Execute the following command to display the Work with Loads panel:
Enter option 1, Load, next to the Load Name for Robot Space and press Enter.
The installation program installs Robot Space, the RBTSYSLIB library (as needed), and two user profiles (RBTADMIN and RBTUSER). It adds RBTSYSLIB to the system portion of your library list, if required.
Note: You only need to enter a license code after installing Robot Space. If you updated Robot Space, skip these steps.
After you load Robot Space to the IBM i, you must enter a license code in order to use the product. If you haven't received a license code, contact your Regional Sales Manager.
Execute the following command on the IBM i to open the Installed Robot Products panel:
Enter option 1 by Robot Space to open the Robot Space License Setup panel.
Copy your new license code. Then, paste it into the first entry field under License Code (it will automatically fill the other fields).
The install program restored two libraries to your IBM i: RBTSPCLIB and RBTSYSLIB.
Three libraries were restored to your system for use during the installation or update process: HSLOADMGR, HSLOADMGRW, and RBTCDRLIB. We don't remove them from your system in case you're doing multiple installations. You can delete them when you're finished.
Note: You can move the library HSLOADMGR to a different system on the IBM i and use it to complete additional installs or updates. For more information, see “Using the HelpSystems Product Loader.”
Set up Robot Space on your system as described in the Robot Space User Guide. If you didn't install the manuals on your PC, you can download them from our website.
Still have questions? We can help. Submit a case to Technical Support.