Read these instructions completely before you begin.
This document provides specific instructions on how to convert Robot Autotune using the HelpSystems Product Loader. For general information about the HelpSystems Product Loader, see “Using the HelpSystems Product Loader.”
Converting from Robot Autotune 7 to 8 requires you to delete the Robot Autotune 7 product library and install 8 as a new installation.
You must have IBM i V7R1 or higher to run Robot Autotune 8.
Robot AUTOTUNE 8 requires a new permanent security code. If you don't have one, contact your Regional Sales Manager.
If you're going to run Robot Autotune and need to upgrade your operating system level to the following, you must apply the specified PTF:
Before loading Robot Autotune, we check if RBTSYSLIB needs to be updated. If it does, you’ll be asked to bring down the subsystem RBTSLEEPER. This ends all Robot products running on your system. When the update completes, the subsystem will restart automatically.
When you’re finished, read the After You Are Done section for additional information.
Make sure ATLIB is in your library list. Enter the following command to print the AT122 report:
This report details your existing performance factors and control values for Robot Autotune. You can use this report as a guide when re-entering the values after reinstalling the product.
Execute the following command to end Robot Autotune:
Execute the following command to delete the Robot Autotune library from your system:
The Robot Autotune installation process downloads everything to your PC and loads the objects on the IBM i. This process is described in the following steps:
Download the Robot Autotune installer (setupAutotune8.exe) from My Downloads page on our website. Double-click it to start it.
On the Choose Components panel, select which components you want to load. You can choose the Manuals and the Software for IBM i. Click Next.
If you’re only installing the manuals, the process completes and the installer closes. The manuals were installed at the following location, and you can skip the rest of these steps.
C:\Program Files (x86)\Help Systems\Robot AUTOTUNE 8\manuals
If you’re loading the Software for IBM i (with or without the manuals), continue to step 4.
On the IBM i Details panel:
Select or enter the IBM i where you want to install Robot Autotune.
Enter a user profile and password that’s a member of the user class *SECOFR and has at least the following special authorities: *ALLOBJ, *SECADM, *JOBCTL, and *IOSYSCFG. The user profile should have Limit capabilities set to *NO. This profile will be used to restore and copy objects, and for product maintenance on the IBM i.
(Optional) In the Advanced Settings section:
Enter a port number or use the arrows if you want to change the FTP port number to something other than the default of 21.
Select Secure File Transfer if you want to use FTPS (FTP over SSL) during the file transfer. The default FTPS secure port is 990, but it can be changed to the required secure port for your environment.
In the Timeout (seconds) field, enter the number of seconds the session should be kept active during an FTP transfer. You can choose anywhere between 25 and 1800 seconds (30 minutes).
Note: If the transfer takes longer than the amount of time specified, the session will expire.
You have two options on the Product Load Options panel:
Click Immediate Load if you’d like to load the product on the IBM i now.
Note: This ends Robot Autotune until the product load completes. After you are done, we’ll restart the product.
Note: See “Loading Staged Objects on the IBM i” below for instructions on how to load the staged objects on your selected IBM i system.
The Product Load Progress panel for Robot Autotune launches. When the processing is complete, you have two choices:
If this is the only installation of Robot Autotune that you're doing, click Finish.
If you have installations to do on other IBM i systems, click Restart. Then, return to step 4.
Note: If the Product Load Progress panel ends with an overall Failed message, the product upload could not complete properly. To find the reason the upload failed, click View Logs and review your logs. You can also use Download at the top of the logs to save the information for future review.
If you chose to stage your objects during step 5b of the conversion process, do the following to manually load them on the IBM i you identified above.
Execute the following command to display the Work with Loads panel:
Enter option 1, Load, next to the Load Name for Robot Autotune and press Enter.
After the install completes, execute the WRKSPLF command to check the spooled files for any errors that may have occurred. If you have any questions, contact Technical Support.
After you've successfully installed Robot Autotune, enter one of the following commands to display the Auto Tune Menu:
ATLIB/ATM or GO ATLIB/ATM
Note: If RBTSYSLIB exists on your system, you can also enter RBO on the command line and select option 3 to display the Auto Tune Menu.
Follow the instructions in the Robot Autotune User Guide to set up Robot Autotune on your system. Use the AT122 report as a guide to re-enter your performance factors and control values. Use the CALL AT900 command and enter your new permanent security code.
Robot Autotune 8 performance factor values default to megabytes (MB). You can specify values using either MB, KB, or a percentage value, but there are limitations. Percentage values are more appropriate for logically partitioned IBM i systems where main storage can change continuously. See the Robot Autotune User Guide for complete information on entering performance factors.
Three libraries were restored to your system for use during the installation process: HSLOADMGR, HSLOADMGRW, and RBTCDRLIB. We don't remove them from your system in case you're doing multiple installations. You can delete them when you're finished.
Note: You can move the library HSLOADMGR to a different system on the IBM i and use it to complete additional installations. For more information, see “Using the HelpSystems Product Loader.”
Still have questions? We can help. Submit a case to Technical Support.