Disk Monitoring using Robot Monitor

The following table contains a list of message IDs, which will be sent if you are using the product.

MessageSeverityMessage text
MON3004 99 Warning: Disk failure for ASP &2, on system &1.
MON3005 00 Warning: Disk ASP &2 synchronizing, on system &1.
MON3006 99 Warning: ASP &2 overflowed on system &1.
MON3007 99 Warning: ASP &2 has failed unit on system &1.
MON3008 99 Warning: ASP &2 has a hardware failure for a unit on system &1.
MON3009 99 Warning: ASP &2 has a unit not ready on system &1.
MON3010 99 Warning: ASP &2 has a write protected unit on system &1.
MON3011 99 Warning: ASP &2 has a degraded unit, on system &1.
MON3012 40 Warning: ASP &2 in parity rebuild state, on system &1.
MON3013 40 Warning: Unallocated disk units on system &1.
MON3018 99 ASP &1 on system &2 has overflowed.
MON3019 99 Warning: Disk &4 in ASP &3 on &2 has a problem: &1.

 

Disk Monitoring using an automated Message Monitoring Tool

The following table contains a comprehensive list of message IDs from the QCPFMSG file, which can be browsed through to select message IDs that you might wish to highlight should they be received. The advice would be to work through them starting at the severity 99 messages, then filter by relevance to your network’s configuration and finally consider what action you wish to take.

MessageSeverityMessage text
CPDB8E1 60 An error occurred trying to vary-on an ASP device.
CPDB8E2 20 A disk device problem was detected.
CPDB8E3 20 A disk device problem was detected.
CPDB8E4 30 ASP device status change not allowed.
CPFBA2A 40 Disk unit &1 not part of a mirrored set.
CPFBA2B 40 Disk unit to be replaced &1 still active.
CPFBA2C 40 Replacement disk unit &1 wrong type or model.
CPFBA2D 40 Replacement disk unit &1 wrong capacity.
CPFBA2E 40 Replacement disk unit &1 already configured.
CPFBA2F 40 Disk unit &1 could not be powered off.
CPFBA25 40 A general DASD Management error has occurred.
CPFBA26 40 ASP event threshold out of range.
CPFBA27 40 Could not restore mirrored data.
CPFBA28 40 Could not resume mirroring on disk unit &1.
CPFBA29 40 Could not suspend mirroring on disk unit &1.
CPFBA3A 40 Create new ASP failed.
CPFBA3B 40 ASP number out of range.
CPFBA3C 40 Cannot replace parity disk unit &1 - old disk unit &1 not in parity set.
CPFBA3D 40 Cannot replace parity disk unit &1 - new disk unit in wrong position.
CPFBA3E 40 Cannot replace parity disk unit &1 - new disk unit is wrong capacity.
CPFBA3F 40 Cannot rebuild parity information.
CPFBA30 40 Disk unit &1 could not be powered on.
CPFBA31 40 Disk unit &1 has errors.
CPFBA32 40 Disk unit &1 not found.
CPFBA35 40 Disk unit &1 configured.
CPFBA36 40 Add mirrored ASP failed - cannot pair units.
CPFBA37 40 Cannot add disk unit &1 - already configured.
CPFBA38 40 Cannot add unprotected disk unit &1 to protected ASP.
CPFBA39 40 Cannot add disk unit. This system has the maximum number of disk units allowed.
CPFBA4E 40 ASP storage threshold value not valid.
CPFBA4F 40 Offset to disk unit resource name array not valid.
CPFBA40 40 Disk unit &1 not part of parity set.
CPFBA41 40 Device parity set not operational.
CPFBA42 40 Disk unit &1 not eligible to be added to device parity protection.
CPFBA48 40 Operation failed with unrecognized return code, &1.
CPFBA49 40 Number of disk unit resource names not valid.
CPFBA50 40 Number of disk unit resource names is out of range.
CPFBA51 40 Array of disk unit resource names was not provided.
CPFBA52 40 Wrong number of disk unit resource names.
CPFBA53 40 Unexpected authority validation error has occurred.
CPFBA54 40 CRG not in correct state for operation.
CPFBA55 40 Geographic mirroring operation failed.
CPFBA56 40 DASD management operation failed.
CPI0945 99 Mirrored protection is suspended on disk unit &1.
CPI0946 99 Mirrored protection is suspended on disk unit &1.
CPI0947 99 Mirrored protection is suspended on disk unit &1.
CPI0948 99 Mirrored protection is suspended on disk unit &1.
CPI0949 99 Mirrored protection suspended on disk unit &1.
CPI095A 80 IASP &1 mirror copy storage threshold reached.
CPI095B 60 Geographic mirroring for IASP &1 has started flow control.
CPI095C 60 Geographic mirroring for IASP &1 has ended flow control.
CPI095D 80 Cross-site Mirroring (XSM) synchronization for IASP.
CPI0950 99 Storage unit now available.
CPI0953 90 ASP &5 storage threshold reached.
CPI0954 90 Storage limit exceeded for ASP &1.
CPI0955 80 System ASP unprotected storage limit exceeded.
CPI0956 99 Mirrored protection suspended on disk unit &1.
CPI0957 99 Mirrored protection suspended on disk unit &1.
CPI0958 99 Mirrored protection suspended on disk unit &1.
CPI0959 99 Mirrored protection suspended on disk unit &1.
CPI096B 99 Geographic mirroring is suspended for IASP &1.
CPI096C 99 Geographic mirroring is still suspended for IASP &1.
CPI096D 99 Copy of IASP has been rejected.
CPI096E 99 Disk unit connection is missing.
CPI096F 99 Failure detected on Mirror Copy node.
CPI0970 99 Disk unit &1 not operating.
CPI0988 40 Mirrored protection resuming on disk unit &1.
CPI0989 40 Mirrored protection resumed on disk unit &1.
CPI099B 90 Critical storage condition exists.
CPI099C 90 Critical storage lower limit reached.
CPI099D 90 System starting in storage restricted state.
CPI099E 90 Storage lower limit exit program error occurred.
CPI0992 99 Errors occurred on disk unit &1.
CPI0996 99 Error occurred on disk unit &1.
CPI0998 99 Error occurred on disk unit &1.
CPI1136 99 Mirrored protection still suspended.
CPI1138 70 Storage overflow recovered for ASP &1.
CPI1139 70 Storage overflow recovery failed for ASP &1.
CPI1158 80 Auxiliary storage exceeds system limits.
CPI116A 99 Mirrored protection suspended on the load source disk.
CPI116B 99 Mirrored protection still suspended on the load source disk.
CPI116C 99 Compressed disk unit &1 is full.
CPI116E 99 Mirrored protection has changed unit.
CPI1161 99 Unit &1 with device parity protection not fully operational.
CPI1162 99 Unit &1 with device parity protection not fully operational.
CPI1165 99 One or more device parity protected units still not fully operational.
CPI1166 40 Units with device parity protection fully operational.
CPI1168 99 Error occurred on disk unit &1.
CPI1169 99 Disk unit &1 not operating.
CPI947A 70 Disk motor problem.
CPI9476 20 Temporary Device Error.
CPI9477 70 Disk subsystem configuration error.
CPI9478 70 Disk command timeout error.
CPI9479 70 Disk Media Error.
CPI9490 70 Disk error on device &28.
CPI95E4 70 Optical Library &25 internal disk unit failed.
CPI95E6 70 Optical Library &25 internal disk unit format error.
CPP0110 70 Controller &26 indicates error on disk unit.
CPP1602 0 Disk device returned wrong response to IOP.
CPP1603 0 Disk or tape device detected recoverable error.
CPP1604 90 *Attention* Impending DASD failure. Contact your hardware service provider now.
CPP1605 0 Disk device detected recoverable error.
CPP29A3 0 Data error, sector reassignment required.
CPP29A4 0 Data error during sector reassignment.
CPP29A8 0 Customer engineer directed to system problem analysis.
CPP29A9 0 Customer engineer directed to disk unit analyzing problem.
CPP29BA 70 Hardware error on device under controller &27.
CPP29BB 70 Configuration error on device &25.
CPP29BD 0 Special device parity protection recovery required.
CPP29BE 0 Spare drive requires service.
CPP29BF 70 Device parity protection suspended on device &30.
CPP29B0 70 Recovery threshold exceeded on device under controller &27.
CPP29B1 0 Predictive Failure Analysis threshold reached.
CPP29B2 0 Disk drive has incorrect capacity.
CPP29B3 0 LRC error.
CPP29B4 0 Disk drive missing from disk array internal configuration.
CPP29B5 0 A disk drive was improperly substituted in the disk array.
CPP29B6 0 Data miscompare error.
CPP29B7 0 Configuration error, minimum configuration assumed.
CPP29B8 70 RAID protection suspended on controller &27.
CPP29DF 0 9337 Service Information, Service Procedures, chapter 4.
CPP29D0 0 Write/read buffer failure due to an interface error.
CPP29D1 0 IO processor cannot degate disk unit from interface.
CPP29D2 0 Disk unit internal interface cable failure.
CPP29D5 0 Slave operational to not operational transition.
CPP29D6 0 Sequence error, unit interface.
CPP29D7 0 Parity error, disk unit interface.
CPP29D8 0 Sync in is not equal to sync out, disk unit interface.
CPP29D9 0 Master transfer not successful, disk unit interface.
CPP29ED 0 Disk array internal configuration error.
CPP29EF 0 Data error, sector rewrite required.
CPP2903 0 Disk drive initialize required.
CPP2904 0 Disk drive is powered off.
CPP2905 0 Additional disk drive required.
CPP8916 0 Disk unit not active.
CPP8917 0 A permanent I/O Processor cache failure occurred.
CPP8918 0 IOP cache data exists for a missing or failed device.
CPP8919 0 Array no longer protected due to missing or failed disk unit.
CPP8920 0 Cache mirror card.
CPP8921 90 IOP &26 failed.
CPP8922 90 Cache mirror card on IOP &26 failed.
CPP8923 90 Cache mirror card on IOP &26 failed.
CPP8924 90 Cache mirror card failed and data loss is possible.
CPP8925 90 IOP &26 has detected a hardware configuration problem.
CPP8926 90 The disk units on IOP &26 are not in the expected configuration.
CPP8927 90 Cache data conflicts with device data on IOP &26.
CPP8928 90 Array protection has been lost on IOP &26.
CPP8929 90 Disk unit requires initialization before use on IOP.
CPP8930 90 IOP &26 detected a hardware configuration problem.
CPP8931 0 Array not functional due to present hardware configuration.
CPP8932 0 Required cache data cannot be located for a disk unit.
CPP8933 90 IOP &26 detected a Licensed Internal Code failure.
CPP8934 0 Disk unit is not supported at its physical location.
CPP8936 70 Device format error reported by I/O Processor &26.
CPP8937 90 Array not functional on IOP &26 because of hardware.
CPP8938 0 A permanent cache mirror card failure occurred.
CPP8939 0 A recoverable cache mirror card error occurred.
CPP8940 80 IOP &26 indicates a recovered error.
CPP8941 80 IOP &26 indicates a recovered error.
CPP8942 90 IOP &26 resources not available.
CPP8943 90 The disk units on IOP &26 are not in the configuration IOP &26 expects.
CPP8944 90 The disk units on IOP &26 are not in the expected configuration.
CPP8945 90 A disk unit on IOP &26 is not supported at its present physical location.
CPP8946 0 The IOP and attached cache adaptor card are not compatible.
CPP8947 90 A disk unit that IOP &26 controls has been changed but not by IOP &26.
CPP8948 0 IOP requires a cache adaptor card but cannot find it.
CPP8949 0 Array protection temporarily suspended.
CPP8950 90 A device attached to IOP &26 failed.
CPP8951 0 Cache data exists for device that has been modified.
CPP8952 0 IOP resources not available due to previous problem.
CPP8953 0 Disk unit has been modified after the last known status.
CPP8954 0 Incorrect hardware configuration change has been detected.
CPP8955 0 Disk unit requires initialization before use.
CPP8956 90 IOP &26 detected an error in a storage device interface.
CPP8957 90 The maximum supported number of functional arrays already exist on IOP &26.
CPP8960 0 Disk unit media format corrupted.
CPP8961 0 Disk unit media format is not correct.
CPP8962 0 Disk unit sector read error.
CPP8963 0 Disk unit permanent failure.
CPP8964 0 Disk unit predicted failure, threshold error type.
CPP8965 0 IOP predicted hardware failure, threshold error type.
CPP8966 0 Disk unit error was recovered, statistical error type.
CPP8967 0 Disk unit data error was recovered, statistical error type.
CPP8968 0 Disk unit media error was recovered, statistical error type.
CPP8969 0 Disk unit sector ID was recovered, statistical error type.
CPP8970 0 Disk unit sector data was recovered, statistical error type.
CPP8971 0 Disk unit bus error was recovered, statistical error type.
CPP8973 70 Disk subsystem configuration error.
CPP8982 90 *Attention* A critical DASD problem has occurred.

 


Still have questions? We can help. Submit a case to Technical Support.

Last Modified On: March 08, 2018